Wiki Page: Using PondMaker
Applies To Product(s): Pondpack Version(s): V8i (build 08.11.01.51) or later Environment: N/A Area: N/A Subarea: N/A Original Author: Scott Kampa, Bentley Technical Support...
View ArticleWiki Page: How do I filter a column in my flextable using a custom query that...
Applies To Product(s): Bentley WaterGEMS, Bentley SewerGEMS, Bentley CivilStorm, Bentley StormCAD, Bentley PondPack, Bentley StormCAD, Bentley HAMMER, Bentley WaterCAD Version(s): 08.11.04.58...
View ArticleForum Post: Darwin Calibrator and Message IDs
Hello 1- I calibrated a model correctly without any problem, but after exporting and running, there were so many errors appeared. Is it logical? Why did not it aware me while calibrating and why it...
View ArticleForum Post: RE: RE: Pattern (Demand )
Hello RSP, A demand needs to have at least two points in order to be valid. Even if the pattern is basically a multiplier (or a pattern that is the same over a 24 hour simulation), similar to the...
View ArticleWiki Page: FATAL ERROR when opening AutoCAD (Solution 500000102601)
Applies To Product(s): WATERCAD Version(s): 08.11.04.50 Environment: N\A Area: Installation Subarea: N\A Original Author: Scott Kampa, Bentley Technical Support Group...
View ArticleForum Post: RE: Darwin Calibrator and Message IDs
Hi Sim, 1- I calibrated a model correctly without any problem, but after exporting and running, there were so many errors appeared. Is it logical? Why did not it aware me while calibrating and why it...
View ArticleForum Post: RE: Darwin Calibrator and Message IDs
2- Some colors e.g. blue or green are not explained in user notification's help. Who knows what these colors want to say? 2) A blue light is an informational message, a green light indicates no...
View ArticleForum Post: RE: Darwin Calibrator and Message IDs
3- Negative pressure results from a mistake in modeling the network. Why it does not appear in user notification as a red error? It is shown blue. 3) This doesn't appear as a red user notification...
View ArticleForum Post: RE: RE: Pattern (Demand )
Thanks Scott. It worked. There is an another problem of no flow in the pumps header beacause of that very high water Age .This issue i posted as a new thread. Thanks, RSP
View ArticleForum Post: High age in pump common header because of low flow
Dear All, I performed age analysis calculation for my water distribution model. I attached the screen shot of the model for reference. Here P-596, P-597, P-598 are the pipelines showing very high...
View ArticleForum Post: Water Distribution Network _ Valve Closure
I have a large water distribution network which is mainly a 600mm water pipeline that feeds 10 different areas (districts) as shown in the attached screenshot. I am doing transient analysis to find...
View ArticleForum Post: RE: High age in pump common header because of low flow
Assuming that you are running an EPS model and the flows displayed are the flow for a given time step, then it looks as if the model did not converge at the time step. Look at the Analysis Calculation...
View ArticleForum Post: RE: Loadbuilder - load estimation by population
I had this same problem and a Google search led me here. I discovered a solution after much tinkering and i'd like to share in case anyone else might have the same problem, despite the fact this is an...
View ArticleForum Post: RE: Darwin Calibrator and Message IDs
Regarding question #3 - I'll add that small negative pressures can occur in a real system in some cases, such as the suction side of a pump.
View ArticleForum Post: Define tank level conditions and constraints
Hi everyone! I’m using WaterGems and I want my model to work like this: the water come from the reservoir and is consumed in node J-1 passing through the turbine and then through the tank. As the...
View ArticleWiki Page: Negative Pressures
Applies To Product(s): Bentley WaterGEMS, Bentley WaterCAD Version(s): 08.11.XX.XX Environment: N/A Area: Modeling Subarea: Original Author: Dan Iannicelli, Bentley Technical...
View Article