Wiki Page: Quantifying pond overflow (Solution 500000057856)
Applies To Product(s): BENTLEY PONDPACK Version(s): N\A Environment: N\A Area: Modeling Subarea: N\A Original Author: Bentley Technical Support Group Problem I have a pond that is overtopping in the...
View ArticleForum Post: USER NOTIFICATION:"There is a gutter leaving this 'In Sag' catch...
Hi for the modelling of a gutter I am getting the following warning message: "There is a gutter leaving this 'In Sag' catch basin inlet. By definition, gutters should flow towards 'In Sag' inlets -...
View ArticleForum Post: RE: USER NOTIFICATION:"There is a gutter leaving this 'In Sag'...
Hamid, I'd like to see your model files because the notifications that you're getting don't make much sense to me based on the screen shot you've included. There are two options for sharing your model...
View ArticleForum Post: RE: set start points of pipes as upstream side
Hello Hamid, The following support solution has details on this:...
View ArticleForum Post: RE: USER NOTIFICATION:"There is a gutter leaving this 'In Sag'...
Hamid, I was able to locate the problem by setting up a model similar to what you have in your screen shot above. The reason that you're getting those user notifications is because you have a gutter...
View ArticleForum Post: RE: USER NOTIFICATION:"There is a gutter leaving this 'In Sag'...
Hi Mark Could you please send me your model? Thanks Hamid Hamid.Akbari@AECOM.COM
View ArticleWiki Page: How do I reverse that start and stop node for a pipe, conduit,...
Applies To Product(s): Bentley WaterGEMS, Bentley SewerGEMS, Bentley CivilStorm, Bentley StormCAD, Bentley PondPack, Bentley SewerCAD, Bentley HAMMER, Bentley WaterCAD Version(s): 08.11.XX.XX...
View ArticleForum Post: RE: USER NOTIFICATION:"There is a gutter leaving this 'In Sag'...
Hamid, After some further analysis of your problem I don't think I was 100% correct in what I previously stated. It's possible that your problem is two fold with the first issue being that GU-1...
View ArticleForum Post: RE: USER NOTIFICATION:"There is a gutter leaving this 'In Sag'...
Actually I am going to just model a flow entering to a gutter and then convey to a ditch inlet and then to pipes. How can I model this? Regards Hamid
View ArticleForum Post: RE: USER NOTIFICATION:"There is a gutter leaving this 'In Sag'...
You can simply connect the catchment directly to the downstream ditch inlet (catchbasin element) and configure the gutter in the catchbasin properties. The spread and depth reported at the catchbasin...
View ArticleForum Post: RE: USER NOTIFICATION:"There is a gutter leaving this 'In Sag'...
Jesse and Mark I appreciate you for your attention to my question, Actually I am a little bit confusing about modelling of "gutter and pipe" and "Spread and depth" measured in the gutter. Typically I...
View ArticleForum Post: RE: How to eliminate spike flow at the inlet of the reservoir?
Hi Mark, I have uploaded the file at secure file. You may have a look at the Tank label R-00017 and attached to it is the reservoir i added to solve the spike problem. tq
View ArticleForum Post: Override Control?
Hello, I have some trouble involved Override Control of "SCADAConnect simulator". I had setup control according to required from system; however, The Pump Station run slightly different comparing with...
View ArticleForum Post: Simulation model
In SCADA connect content variety of "Simulation Type" such as, Base line initial condition, historical, live. Please tell me difference among them. Thanks,
View ArticleForum Post: RE: How to use Darwin Scheduler to optimise system for optimal...
Sorry I wasn't clear with my description. I guess there's two things. Firstly, based on the specified minimum and maximum tank level, what is the optimum pump schedule. Secondly, are these levels good...
View ArticleForum Post: Unexplained flow of pumps in WaterCad
Hello, I have a very strange, contradicting results of WaterCad. Let me get straight to the point, the following is a summary of inputs, outputs, and the problem A- Model inputs: - Friction method:...
View ArticleForum Post: RE: Override Control?
Hello Dang, As long as the Control Override is created and enabled, the override that you enter should take precedence over the control in the model. Please see the Control Override section in the...
View ArticleForum Post: RE: Simulation model
Hello Dang, Please review the following TechNote on SCADAConnect Simulator: http://communities.bentley.com/products/hydraulics___hydrology/w/hydraulics_and_hydrology__wiki/16992.scadaconnect-simulator...
View ArticleForum Post: RE: Unexplained flow of pumps in WaterCad
Hello Ahmed, If I am understanding the issue correctly, the system head curve shown in Figure 2 is still only from one pump, not all three pumps that are operating. Instead of a single system head...
View ArticleForum Post: RE: How to use Darwin Scheduler to optimise system for optimal...
Debbie, Re: "what is the optimum pump schedule" With the tank range you have entered and other constraints, Darwin Scheduler will attempt to find the "optimum" pump schedule that results in either the...
View Article